Search results

Hi all, does anyone know a place that does the FRP map cheap. Is there a option to have it on a chip to plug in to the OBD port, or does it really have to be mapped onto the ECU? Thanks in advance.

https://www.youtube.com/watch?v=CZ1q3fhihCE] At 0:22 in the above video, when he lets off the rev, you can hear a whooshing noise, like it has an aftermarket air filter. Is that normal, as my Puma has never done it?

Hi all, where can I buy the inlet manifold gasket that sits to the cylinder head? I can't find one, and Ford state they no longer make them.

Hi all, done the timing kit & seals from new engine. Had to get flywheel resurfaced as well, as upon stripping it, noticed it's been eating the clutch. :roll: Anyway, after doing two revulations of the engine, I've noticed when I put the camshaft bar back in (which went in fine) that the...

Hi all, I'm wondering if the left camshaft bolt has to renewed? I know the VCT one on the right camshaft needs to be.

Hi all, has anyone got a decent quality picture of what the timing tensioner looks like on the actual car when its done correctly? I want to see how the backing plate sits when it's done correctly, the Gates timing guide only has pictures off it when it isn't installed. Thanks.

Hi all, as the title suggests my camshaft sensor is out 180 degrees. I put mine in the block and put the bolt through it, looking through puma projects the other day, I noticed it has a metal clip holding it the other way around? (Image is a project off the internet note the metal clip...

Hi all, after a 1.7 Puma lump preferably with alternator, but don't need A/C compressor or the PAS. Want one in the low 80,000 or below. Preferably one with a registration to back the mileage up, and if possible service history for the engine.

Hi all, finally put my engine back in after an overhaul. I've put a new lambda sensor in, and checked all the usual suspects, swapped the ICV with a spare one. It just won't idle whatsoever, the revs drop below 1,000rpms and it stalls out. Even with the clutch in. I've swapped the coil pack...

Hi all, has anyone got a picture of a puma of the front of the engine bay without the radiator? I've forgotten how the metal clip goes under the starter motor on the gearbox. :roll: Would also like to see how the wiring harness goes around the front of the block. Thanks.

Hi all, there's a cheap £150 4-2-1 on eBay, which is identical to Milltek's 4-2-1 which is £400, and will require custom welding to go onto the Puma catback. Whereas the cheap £150 one has the correct flange to just bolt up the Puma catback I already have. They're probably made with the exact...

Hi all, I'm putting a TAPE ECU on to a DIVE loom, obviously the DIVE has 2 lambda sensors, whereas the TAPE has 1. Which one from the DIVE wiring loom do I use, the blue or green one on my decat? Also other than moving the 80 pin to 75 on the wiring loom is there anything else I've forgot to...

Hi all, wondering what's good preventative maintenance on the 1.7 engine. I have the engine out the car, current plans are new clutch, and flywheel lapped out by an engineer. Cambelt, both crank seals gearbox & cambelt side. Also new rocker cover gasket, new oil sump gasket (both parts) and...

Hi all, is there a method to removing the suction cup thing in the bulkhead to remove the wiring from the footwell? I tried popping it out but it seems glued in, I ran out of light and called it a day, but is there a method to removing it? Thanks in advance.

Hi, does anyone have any of the above? I'm after a 4-2-1, some kind of aftermarket backbox that sounds decent and isn't too big, around 3" is ideal. Also need a TAPE ECU.

Hi all, there's a wire going from the main fuse box under the bonnet through the car to behind the fuel pump wires, which sit on top of the rear axle beam, just wondering what it is for? I'm assuming it's an ABS sensor.

Hi all, wondering how many silencers the standard puma exhaust has? I've sourced a catback and backbox and it only has one silencer, I'm sure the Fiesta's have two silencers, thought the Puma would have the same silencer configuration?

Hi all, I'm breaking an X reg DIVE Puma. All parts available apart from engine, engine wiring loom and gearbox. I ain't taking any of the suspension parts off as I'm going to tow it scrapyard with a Jeep. I'm probably going to have to break one of the back side windows as I've...