Search results

Hi and thanks for the offer. Managed to source a couple locally now thanks. Also yeah, tbh would have been a bit of a distance to travel all the way from Essex!!. Cheers for the reply anyway.

Hi all. Preparing my Puma to be a track car and almost finished now. Stripped all interior, changed steering wheel for MOMO one, removed p/side airbag also. So I've got the age old problem of the light on the dash perm illuminated!!. Have removed the fuse for the system, pretty sure fuse 14...

Hi all. After a set of fiesta mk3.5 seat subframes/runners both sides please, or especially the drivers side if poss. Must be in good condition/ working order please, WHY people please. Thanks, Jim.

Bump!, anyone please :-( WHY???. Thanks all.

Hi and cheers for the reply. If you mean side mounts?,I already have these mounted on a set of cobra imola's I have. I have a set of genuine Cobra vehicle specific subframes already, that bolt direct to the Puma floor. Just needed a set of original front seats for the frames/runners off of...

Phew indeed!. Yes Barry, last time we ran it up the rattling wasn't there :-), she sounds real nice, going to be noisy in the cabin that's for sure. Jim.

Well Barry, gents, bled the brakes today with no issues at all!. Have got an absolutely brilliant pedal tbh. Myself and my son did them twice to be sure of no air in system. Have to be honest was a little worried beforehand we may have a problem with air in the system. Now I feel quite...

Hi all. As above, after a cheap as poss set of front seats. I'm only really after the subframes/runners, so must be in as good a cond as poss and good working order. Can and will collect if local enough. I'm in the Essex area, not far from Basildon, Corringham/ Stanford Le Hope...

Hi. I'm after a a set of front seat runners/subframes both sides, in as good a condition as possible and as cheap as poss :grin:. They are for a project I'm working on. Could take the pair of front seats complete if cheap enough. We're over in Corringham, so real local to you. Any...

Hi Barry, thanks for the reply and will look into posting some pics when I get a bit of time. Car's all up and running today, sounds great and looks like the lambda extension worked :grin:. When I do rev her slightly higher though, I've got a rattle coming from what I reckon is the ABS pump...

Hi Barry. Yes you're right these little beuts do seem to have quite a good following and a broad age range too :grin:. Had a good read through most of your project!, lots of pages. All really good stuff indeed, lot of care and time spent," man after my own heart". I'm not quite up on...

Was an absolute bargain Barry. I do know what you mean, would have made a great standard car with a bit of work and a couple of hundred quid. Unfortunately have been working on her now for a while and almost ready o rock and roll :grin: . Probably spent about £1500 on it now, has ap coilovers...

Oh, is a 99 on a T plate, absolute bargain 200 quid with a spare set of props too!!!!!!, in Radiant red. Ticks all the boxes for us, no aircon, big thumbs up!, tape ecu, single lambda, all good. Jim.

Nice one Barry. Rain stopped plat atm! :-( , we're getting the worst of it down in the south east atm. Anyway thanks for your prompt replies, you seem like a top bloke and very like minded I think. So just quickly, have been into my cars since knee high and like you had some nice stuff along...

I get that big time!, proper old Skool saying :grin:, may be putting myself down a little but only the slightly older generation folks amongst us would get that. Hi anyway's, Jim.

Hi all. Have just extended the lambda sensor loom for fitting to sensor on a Milltek 4 branch manifold, later type with the section of flexi pipe built in. Any suggestions/ ideas on the best route for the bit of loom with plug on to go down to lower part of manifold where the sensor is...

Hi all. Have just extended the lambda sensor loom for fitting to sensor on a Milltek 4 branch manifold, later type with the section of flexi pipe built in. Any suggestions/ ideas on the best route for the bit of loom with plug on to go down to lower part of manifold where the sensor is...

All done Barry, used the wire from an old lambda sensor I had knocking around, seemed to be about the right gauge!!.... My soldering wasn't brilliant tbh, but did twist wires together pretty good beforehand, seemed strong enough I think. Looking now at how best to route the cable down to the...

Hi Barry, cheers for he replies and apologies for not getting back sooner. Our little English bull terrier puppy's been taking up all our time!!!. Thanks for the info and comments, will get around to it hopefully sooner rather than later :| .

Cheers for the reply Barry. Car and engine running spot on prior to works, no lights up, engine really sweet. So, just to be sure, just a case of letting in some wire of the same thickness/ampage?. This will i take it mean cutting, soldering twice for each wire, if you know what i mean!! :? ...